during boot, few errors comes up.
How to make them away?
Any Idea is welcome. I will search the net with any recommendation.
Code: Select all
...
[ 5.442740] media: Linux media interface: v0.10
[ 5.464114] Linux agpgart interface v0.103
[ 5.467498] intel_rng: Firmware space is locked read-only. If you can't or
[ 5.467498] intel_rng: don't want to disable this in firmware setup, and if
[ 5.467498] intel_rng: you are certain that your system has a functional
[ 5.467498] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 5.485807] agpgart-intel 0000:00:00.0: Intel 915G Chipset
[ 5.485926] agpgart-intel 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
[ 5.486308] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[ 5.486727] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 5.494564] [drm] Initialized drm 1.1.0 20060810
[ 5.559196] iTCO_vendor_support: vendor-support=0
[ 5.559823] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 5.559874] iTCO_wdt: Found a ICH6 or ICH6R TCO device (Version=2, TCOBASE=0xf860)
[ 5.560114] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 5.603924] Linux video capture interface: v2.00
[ 5.828775] i915 0000:00:02.0: setting latency timer to 64
[ 5.829181] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 5.829187] [drm] Driver supports precise vblank timestamp query.
[ 5.829248] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 5.830415] [drm] initialized overlay support
[b][ 5.849459] i2c i2c-1: sendbytes: NAK bailout.
[ 5.849955] i2c i2c-1: sendbytes: NAK bailout.
[ 5.850442] i2c i2c-1: sendbytes: NAK bailout.
[ 5.877026] [drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder is 130
[ 5.877067] Raw EDID:
[ 5.877095] 00 ff ff ff ff ff ff 00 ff ff ff ff ff ff ff ff
[ 5.877194] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff[/b]
[b][ 5.877292] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.877390] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.877487] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.877586] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.877683] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.877781] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.904552] [drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder is 130
[ 5.904727] Raw EDID:
[ 5.904822] 00 ff ff ff ff ff ff 00 ff ff ff ff ff ff ff ff
[ 5.904920] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.905019] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.905117] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff[/b]
[b][ 5.905215] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.905315] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.905434] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.905550] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.932284] [drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder is 130
[ 5.932460] Raw EDID:
[ 5.932555] 00 ff ff ff ff ff ff 00 ff ff ff ff ff ff ff ff
[ 5.932654] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.932751] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.932850] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.932948] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff[/b]
[b][ 5.933046] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.933144] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.933242] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.949343] pwc: Logitech QuickCam Zoom USB webcam detected.
[ 5.960031] [drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder is 130
[ 5.960209] Raw EDID:
[ 5.960306] 00 ff ff ff ff ff ff 00 ff ff ff ff ff ff ff ff
[ 5.960405] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.960504] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.960603] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.960702] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.960800] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.960899] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 5.960997] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff[/b]
[b][ 5.961101] i915 0000:00:02.0: VGA-1: EDID block 0 invalid.
[ 5.968471] i2c i2c-1: sendbytes: NAK bailout.
[ 5.969029] i2c i2c-1: sendbytes: NAK bailout.
[ 5.969589] i2c i2c-1: sendbytes: NAK bailout.
[ 5.970146] i2c i2c-1: sendbytes: NAK bailout.
[ 5.970700] i2c i2c-1: sendbytes: NAK bailout.
[ 6.008471] i2c i2c-1: sendbytes: NAK bailout.
[ 6.009029] i2c i2c-1: sendbytes: NAK bailout.
[ 6.009584] i2c i2c-1: sendbytes: NAK bailout.
[ 6.010139] i2c i2c-1: sendbytes: NAK bailout.
[ 6.010693] i2c i2c-1: sendbytes: NAK bailout.[/b]
[ 6.016120] fbcon: inteldrmfb (fb0) is primary device
[ 6.093457] Console: switching to colour frame buffer device 128x48
[ 6.098238] fb0: inteldrmfb frame buffer device
[ 6.098241] drm: registered panic notifier
[ 6.098252] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 6.147963] pwc: Registered as video0.
[ 6.148101] input: PWC snapshot button as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/input/input5
[ 6.148277] usbcore: registered new interface driver Philips webcam
[ 6.360719] usbcore: registered new interface driver snd-usb-audio
[ 6.441450] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[ 6.860038] intel8x0_measure_ac97_clock: measured 52831 usecs (2546 samples)
[ 6.860044] intel8x0: clocking to 48000
[ 9.634051] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 9.908319] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 13.796569] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 15.302166] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 15.427960] NET: Registered protocol family 17
[ 15.452701] RPC: Registered named UNIX socket transport module.
[ 15.452709] RPC: Registered udp transport module.
[ 15.452713] RPC: Registered tcp transport module.
[ 15.452717] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 15.486570] FS-Cache: Loaded
[ 15.508996] FS-Cache: Netfs 'nfs' registered for caching
[ 15.556151] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 16.858459] tg3 0000:40:00.0 eth0: Link is up at 100 Mbps, full duplex
[ 16.858466] tg3 0000:40:00.0 eth0: Flow control is on for TX and on for RX
[ 16.858514] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.097780] lp: driver loaded but no devices found
[ 17.626907] ppdev: user-space parallel port driver
[b][ 19.816476] i2c i2c-1: sendbytes: NAK bailout.
[ 19.817853] i2c i2c-1: sendbytes: NAK bailout.
[ 19.818313] i2c i2c-1: sendbytes: NAK bailout.
[ 19.818773] i2c i2c-1: sendbytes: NAK bailout.
[ 19.819232] i2c i2c-1: sendbytes: NAK bailout.
[ 19.819692] i2c i2c-1: sendbytes: NAK bailout.
[ 19.824491] i2c i2c-1: sendbytes: NAK bailout.
[ 19.824972] i2c i2c-1: sendbytes: NAK bailout.
[ 19.825454] i2c i2c-1: sendbytes: NAK bailout.
[ 19.825928] i2c i2c-1: sendbytes: NAK bailout.
[ 19.826401] i2c i2c-1: sendbytes: NAK bailout.
[ 19.848471] i2c i2c-1: sendbytes: NAK bailout.[/b]
[b][ 19.848936] i2c i2c-1: sendbytes: NAK bailout.
[ 19.850308] i2c i2c-1: sendbytes: NAK bailout.
[ 19.850768] i2c i2c-1: sendbytes: NAK bailout.
[ 19.851228] i2c i2c-1: sendbytes: NAK bailout.
[ 19.851688] i2c i2c-1: sendbytes: NAK bailout.
[ 19.852211] i2c i2c-1: sendbytes: NAK bailout.
[ 19.860494] i2c i2c-1: sendbytes: NAK bailout.
[ 19.860959] i2c i2c-1: sendbytes: NAK bailout.
[ 19.861420] i2c i2c-1: sendbytes: NAK bailout.
[ 19.861880] i2c i2c-1: sendbytes: NAK bailout.
[ 19.862339] i2c i2c-1: sendbytes: NAK bailout.
[ 19.901433] i2c i2c-1: sendbytes: NAK bailout.[/b]
[b][ 19.901897] i2c i2c-1: sendbytes: NAK bailout.
[ 19.902358] i2c i2c-1: sendbytes: NAK bailout.
[ 19.902817] i2c i2c-1: sendbytes: NAK bailout.
[ 19.903279] i2c i2c-1: sendbytes: NAK bailout.[/b]
[ 237.532034] usb 1-7: new high-speed USB device number 4 using ehci_hcd
[ 237.666836] usb 1-7: New USB device found, idVendor=058f, idProduct=6387
[ 237.666843] usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 237.666847] usb 1-7: Product: Mass Storage
[ 237.666851] usb 1-7: Manufacturer: USB 2.0
[ 237.666855] usb 1-7: SerialNumber: C38DE82D
[ 237.667487] scsi7 : usb-storage 1-7:1.0
[ 238.664999] scsi 7:0:0:0: Direct-Access USB 2.0 Flash Disk 8.07 PQ: 0 ANSI: 2
[ 238.668737] sd 7:0:0:0: [sdb] 2013184 512-byte logical blocks: (1.03 GB/983 MiB)
[ 238.669239] sd 7:0:0:0: [sdb] Write Protect is off
[ 238.669250] sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 238.670993] sd 7:0:0:0: [sdb] No Caching mode page present
[ 238.671002] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 238.673840] sd 7:0:0:0: [sdb] No Caching mode page present
[ 238.673847] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 238.697445] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 238.697825] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 238.697961] sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 239.509096] sdb: sdb1
[ 239.511298] sd 7:0:0:0: [sdb] No Caching mode page present
[ 239.511306] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 239.511311] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 473.457863] usb 1-7: USB disconnect, device number 4
[ 477.296033] usb 1-7: new high-speed USB device number 5 using ehci_hcd
[ 477.430972] usb 1-7: New USB device found, idVendor=058f, idProduct=6387
[ 477.430978] usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 477.430983] usb 1-7: Product: Mass Storage
[ 477.430987] usb 1-7: Manufacturer: USB 2.0
[ 477.430991] usb 1-7: SerialNumber: C38DE82D
[ 477.431635] scsi8 : usb-storage 1-7:1.0
[ 478.429150] scsi 8:0:0:0: Direct-Access USB 2.0 Flash Disk 8.07 PQ: 0 ANSI: 2
[ 478.431050] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 478.435242] sd 8:0:0:0: [sdb] 2013184 512-byte logical blocks: (1.03 GB/983 MiB)
[ 478.435735] sd 8:0:0:0: [sdb] Write Protect is off
[ 478.435745] sd 8:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 478.436340] sd 8:0:0:0: [sdb] No Caching mode page present
[ 478.436350] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[ 478.439123] sd 8:0:0:0: [sdb] No Caching mode page present
[ 478.439135] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[ 478.668156] sdb: sdb1
[ 478.670369] sd 8:0:0:0: [sdb] No Caching mode page present
[ 478.670378] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[ 478.670384] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[b][ 555.388487] i2c i2c-1: sendbytes: NAK bailout.
[ 555.389885] i2c i2c-1: sendbytes: NAK bailout.
[ 555.390346] i2c i2c-1: sendbytes: NAK bailout.
[ 555.390826] i2c i2c-1: sendbytes: NAK bailout.
[ 555.391287] i2c i2c-1: sendbytes: NAK bailout.
[ 555.391746] i2c i2c-1: sendbytes: NAK bailout.
[ 555.397400] i2c i2c-1: sendbytes: NAK bailout.[/b]
[ 1842.748871] usb 1-7: USB disconnect, device number 5
...